This paper presents a detailed assessment of the value of photovoltaic energy within the German energy supply structure, taking into account the correlation between actual consumption and local power generation. Contrary to previous statistical approaches, this paper takes a new dynamic approach, modelling the dynamic behaviour of the PV power generation as a one-year time series. A comparison with the time series of the power demand allows assessment of the value of PV energy. The value of PV energy mainly results from its ability to substitute conventional power generation and the benefit of this kind of decentralized power generation for network stability and quality. An evaluation of these aspects is carried out for the year 2005 and a likely scenario in 2015.
Back-sheet materials for photovoltaic modules serve several purposes such as providing electrical insulation, environmental protection and structural support. These functions are essential for modules to be safe for people working near them and for the structures to which they are attached. To ensure that all modules meet a minimum set of requirement, they must pass qualifications tests such as IEC 61646, 61215, 61730, and 62108. This paper puts forward the design and composition requirements of back- and front-sheet materials for achieving the highest possible quality performance from PV modules.
Apart from some obstacles and bureaucratic hindrances, the Italian PV market has recently joined the upper echelons of the solar industry. Along with small and medium-sized systems, the commercial and large-scale segment in particular has a great deal of promise. Even though the local industry is still trying to block the domestic market from international competitors, increasing numbers of foreign investors are entering the market. In this close-up of the Italian PV market, the country’s participation in the solar energy industry is reviewed and a projection to 2010 is given, with particular emphasis on the country’s potential to be a major player in the large-scale installation sector.
The reliability of United Solar Ovonic (Uni-Solar) triple-junction amorphous-silicon thin-film photovoltaic modules is critical to their success in an increasingly competitive PV market. Modules must show useful operating lifetimes of 20 to 30 years, and although module efficiency is very important, the total energy that a module will produce largely depends on its operating lifetime. Thus, module reliability must be evaluated to estimate lifetime and establish customer warranty periods. While real-world outdoor exposure testing is necessary and important, accelerated environmental test methods must also be utilized to provide more rapid feedback regarding failure modes, design flaws and degradation mechanisms. The following paper gives an overview of the methodology used to ensure long-term reliability of Uni-Solar flexible thin-film modules.
Anyone familiar with the PV industry can attest to the remarkably accelerated pace of innovation aimed towards generating solar power more cost effectively relative to conventional means of producing electricity. Many of high-technology’s best minds are bringing expertise in materials, manufacturing process, and electronics to tackle the challenge. The resultant gains in cost effective manufacturing, silicon availability and greater irradiance conversion efficiency will make continuous and sustainable impact to cost per kW generated akin to the predicable improvements in transistors per mm2 which has fuelled the semiconductor industry for the past 25 years (although we are not yet so bold as to devise the PV version on Moore’s Law). As less than 0.01% of electricity generated comes from PV installations [1], demand will materialize and the need for public subsidies will decline as the economics improve. This paper will investigate the steps required to make every solar project a “perfect” project by putting forth parameters for evaluating solutions for the problem areas.
Solar enterprises will each be faced with the occasional surplus or lack of solar modules in their lifetimes. In these instances, it is useful to adjust these stock levels at short notice, thus creating a spot market. Spot markets serve the short-term trade of different products, where the seller is able to permanently or temporarily offset surplus, while buyers are able to access attractive offers on surplus stocks and supplement existing supply arrangements as a last resort.
The use of perfluorinated gases such as NF3, CF4 or SF6 for PECVD (plasma enhanced chemical vapor deposition) chamber cleaning has a much higher impact on global warming than does the use of onsite-generated F2. This holds true even when supposing that in the future much more effort is paid for the correct abatement and a leak-free supply and take-back chain. This paper will discuss the steps available to the PV industry for control and reduction of carbon emissions in the chamber cleaning process.
The costs of a photovoltaic installation are driving the market and the need for subsidized schemes, such as feed-in tariffs. Concentrated photovoltaics (CPV) is leading the development of future lowcost renewable energy sources in two ways: on one hand offering high efficiency systems, and on the other, being most capable of reducing manufacturing costs. The idea to decrease the cost of the photovoltaic system using optical elements to focus the radiation into the cell to reduce the size of the cells has been in the mind of the scientists since the 1970s [1]. But, apart from a reduced market, there were several issues that did not allow CPV success at that time. This paper puts forth the proposition that the key is to replace the area of active material, which is the most expensive, with optic elements, which are well known and cheaper.
Although the entire solar manufacturing industry, from raw materials to finished modules, has enjoyed strong double-digit growth rates over the past several years, few sectors have soared like the amorphous-silicon thin-film photovoltaic equipment space. Much of this prodigious multibillion-dollar booking activity can be attributed to the acceptance of the turnkey production packages offered by the likes of Applied Materials, Oerlikon and Ulvac. These suppliers’ plug-and-play, standard toolset solutions are attractive to companies seeking to get into the TFPV module business on a fast track and then scale up their capacities in multimegawatt chunks to achieve grid-competitive cost-per-manufactured-watt metrics.
With the thin-film silicon industry facing the problems of high-quality material deposition at high rates and narrowing deposition process windows, the “no-drift regime” is an important part of this development. In the case of the plasma-enhanced chemical vapor deposition (PECVD) of thin silicon films, the inconstancy of the concentration of silicon-containing particles (SCP) in the plasma leads to changes in deposition conditions, causing a deterioration of film properties, and, therefore, decreasing the performance of the solar cells. During the last few decades, evidence about the process instabilities has been accumulated in different laboratories. In this study, Fourier transform infrared absorption spectroscopy (FTIR), optical emission spectroscopy (OES), self-bias voltage and plasma impedance controls were applied as in-situ process diagnostics during the deposition of amorphous and microcrystalline silicon thin-films. Results of the study were then discussed.
